Paragon Options

Please add any of the following options to your shopping cart.

Power options available on all kilns:

208v (instead of 220/240) This is normally only in schools and industrial buildings	$0	FREE
3 phase power (no charge for Dragon or Viking)	$50	$45
Option: 50 Hz, no charge	$0	FREE
480v, 3 phase power	$225	$215

Options (available on most manual and digital models):

Option: Heavy Duty Rolling Kiln Stand with 2" Steel casters (18" square x 12" high, for 7 and 8 sided kilns.) 27 lbs		$113
Option: Heavy Duty Rolling Kiln Stand with 2" Steel casters (24" square x 12" high, for 10 and 12 sided kilns.) 37 lbs.		$130
Option: Lid Safety Switch. Turns off power to the heating elements when the lid is raised.	$70	$65
Option: Kiln Vent See Orton Vents See L&L Vent See Skutt Vent

Options (available on Digital kilns only):

Option: Three Zone firing control, with type K thermocouples (available on 10 and 12 sided kilns and Dragon kiln) Zone control has 3 separate thermocouples in the kiln, at the top, middle and bottom. It ensures better temperature uniformity. Kilns with zone control typically fire a little slower because hot sections will slow down to allow cooler sections to catch up.	$155	$135
Option: Upgrade to type S thermocouple. Type S thermocouples last much longer than Type K, especially when firing at high temperatures or in harsh environments.	$200	$175
Option: Three Zone firing control, with type S thermocouples (available on 10 and 12 sided kilns and Dragon kiln)	$530	$468
Option: AOP (Auxiliary Output Connector) 240v 6-15 outlet on digital 8, 10 and 12 sided kilns. This is a relay powered electrical receptacle mounted to the kiln. Using the electronic controller, you can plug a loud bell into the outlet and have the kiln alarm when it reaches a certain temperature. Or you can plug your vent into this outlet and use the controller to control when the vent turns on or off. IF YOU ARE BUYING A VENT AND WANT TO USE IT WITH THE AOP, YOU MUST REQUEST 240V VENT IN THE COMMENTS WHEN YOU CHECK OUT. BY DEFAULT YOU WILL GET A 120V VENT.	$95	$90
Option: Mating 6-15 plug for the AOP. Perfect if you purchase the 240v Orton Ventmaster to go with your kiln. (The Ventmaster does not come with a plug on it's cord.)	$15	$14
Option: RS232 port on digital kilns (so you can monitor the kiln from a computer)	$360	$315
Option: Kiln Sitter & Timer backup to electronic controller	$350	$315	ask
If you need a 6-30 or 6-50 receptacle you can buy one here

Paragon Kiln Posts (only for purchase with a Paragon kiln)

1.5" thick are recommended. 1" thick are ok for low fire temperatures especially at the taller lengths. These would be best for small kilns. Although the 1" thick are available up to 10" we do not recommend they be used that tall. Use 1.5" thick instead.

Height	1" square		1 1/2" square
1/2 "	$1.05			NA
1"	$1.20		$1.25
2"	$1.40		$1.75
3"	$1.90		$2.40
4"	$2.30		$2.90
5"	$2.75		$3.35
6"	$2.80		$3.60
7"	$3.15		$4.00
8"	$3.55		$4.15
9"		NA	$4.80
10"	$4.20		$5.00
12"		NA	$6.00