|
Please add any of the following options to your shopping cart.
Power options available on all kilns:
| 208v instead of 220/240v (normally only in
schools and industrial areas) |
$0 |
$FREE |
|
| 3 phase power |
$0 |
$FREE |
|
| Option: 50 Hz, no charge |
$0 |
$FREE |
|
| 480v power: Piece 1: Uses the
regular control panel with some minor modifications but with 600v rated
parts. These panels work fine but are not MET listed to UL499 |
$650 |
$650 |
|
| 480v power: Piece 2: Upgrade to a
NEMA1 control panel which is larger, heavier duty, floor standing, and
more industrial. Then meets UL499. |
$650 |
$650 |
|
Options (available on most manual and digital models):
Options (available on Digital kilns only):
| Option: Optional Kiln Sitter for backup
safety device (or to use as
final control device while still using the control for ramping ) |
$650 |
$650 |
|
| Option: High Limit electronic
control turns off power with separate backup safety contactor (alternative to
KilnSitter backup) Available on Hercules, Easy Load and DaVinci
Kilns only. |
$650 |
$650 |
|
| Option: Type S thermocouples (order 2 for 2
section kilns, 3 for 3 or more sections) |
$185 |
$185 |
|
| Option: 120v Control Power with Noise Filter
(*2) |
$185 |
$185 |
|
| Option: KISS Computer Software to monitor
control with USB cable |
$575 |
$575 |
|
| Handheld Dynatrol Controller |
no longer available
except on DaVinci Models where it is standard |
| If you need a 6-30 or
6-50 receptacle you can buy one
here |
Spare Parts
Kiln Shelves: (ONLY IF ORDERED WITH AN
L&L KILN!)
| |
Full Shelves |
Half Shelves |
| 9" diameter shelf for Baby-Doll Kiln |
$26 |
|
$16 |
|
| 15" diameter shelf for 16.5"
Diameter Kilns (Liberty Belle 3", J18-3) 5/8" thick |
$38 |
|
$23 |
|
| 15.5" diameter shelf for 17.5"
Diameter Kilns (Liberty Belle 2.5", J18) 5/8" thick |
$38 |
|
$23 |
|
| Round 20" diameter shelf for 22" Diameter
Kilns (e23s-3, e23T-3, Jupiter 23xx kilns with 3" brick)
3/4" thick |
$75 |
|
$37 |
|
| Round 21" diameter shelf for 23" Diameter
Kilns (e23s, e23T, Jupiter 23xx kilns with 2.5" brick)
3/4" thick |
$76 |
|
$38 |
|
| Round 26" diameter shelf for 28" and
29" Diameter Kilns (e28S, e28T, Jupiter 29xx kilns with
2.5" or 3" brick) 5/8" thick |
NA |
|
$63 |
|
Triangular Posts (1"
Triangular) ONLY ORDERED WITH KILN
| 1/2" |
$1.90 |
|
|
4" |
$2.85 |
|
| 1" |
$1.95 |
|
|
5" |
$3.20 |
|
| 1.5" |
$2.00 |
|
|
6" |
$3.85 |
|
| 2" |
$2.20 |
|
|
8" |
$4.80 |
|
| 2.5" |
$2.25 |
|
|
10" |
$5.85 |
|
| 3" |
$2.40 |
|
|
12" |
$6.40 |
|
Square Posts (1.5"
Square) Recommended for mid to high fire
ONLY ORDERED WITH KILN
| 1/2" |
$2.45 |
|
|
6" |
$5.20 |
|
| 1" |
$3.20 |
|
|
8" |
$6.20 |
|
| 2" |
$3.80 |
|
|
10" |
$7.85 |
|
| 4" |
$4.15 |
|
|
12" |
$9.55 |
|
Options (for X3200 and T3400 DaVinci Series kilns)
 |
Option: Optional "Bell-Lift" system for
easy loading |
$4675 |
$4675 |
|
 |
Option: Optional Powered bottom. Reduced
heat-up times and cold spots. |
see individual kilns |
(1) Vents exhaust harmful fumes, improve colors and reduce
temperature variation throughout the kiln. It is easier to fire
because you don't have to leave the lid propped at the beginning of
firing.
(2) Some people have unstable power grids with a lot of electrical
noise. This option provides a separate 120v cord to supply power
to the control circuit. This goes through an EMF noise filter to
reduce electromagnetic noise to the control. You can plug this
into a computer UPS or other computer grade surge protector for further
protection.
|
|
